PRECAUTION
1. You can install the camera indoors or outdoors.
2. Choose an ideal location for the camera, since a camera
unit must be protected against vibration.
3.
Be careful not to scratch the lens or dome cover.
4. Use the camera within the temperature(-10 ~ +50 ).
5. Handle with care. Dropping it can cause serious dam-
age to the camera.
6. Avoid any direct sun light toward the lens.
7. Use the AC adaptor 12V DC regulated.(1A recom-
mendddded)
(24V AC available-Dual power version only) of time.
◐FEATURES
1. IP67(Waterproof)
2. Durable MATERIAL : Body-Aluminum,
Dome : Polycarbonate
3. Wall & Ceiling mount available
4. New method to adjust the camera direction
DIMENSION
INSTALLATION
1-1. Ceiling mount installation
1-2. Mounting camera to electrical box
1-3. Pipe application
(1) Remove the bolt, the cable fixing screw and the
cable plug on the bottom of the base.
(2) Use the TEPLON tape to wipe the pipe.
(3) After distributing cables, combine the pipe with the
base.
1-4. Camera direction adjustment and fixing
(1) Cover can be installed four directions using two screws
beside the cover.
(2) After loosening two screws on the cover, you can
adjust the direction of camera.
(3) You can tighten up two screws again to fix the direction.
2. Wall mount installation
3. Finishing installation
◐CONFIGURATION
◐HOW TO USE THE JOG LEVER
(1) MENU : To access the main setup menu. Push
this button for 1 second.
(2) TELE / UP : To close in on a far object.(ZOOM-IN)
/To move the arrow indicator to up.
(3) WIDE / DOWN : To widen the view.(ZOOM-OUT)
/ To move the arrow indicator to down.
(4) NEAR / LEFT : To see a near object clearly.
/ To move the arrow indicator to left.
(5) FAR / RIGHT : To see a far object clearly.
/ To move the arrow indicator to right.
(6) EXT. VIDEO : Plug your test monitor in here.
(The cable is option)
Set Camera Title String and
OSD Display Position.
ATW–MODE :
OUTDOOR
INDOOR
ATW is controlled by color
tem-perature range
*MODE
- INDOOR : 3000~10,500°K
- OUTDOOR : level
OFF / LOW /
MIDDLE /
HIGH
AREA(4 Programmable zone/
SIZE)
The words "MOTION
DETECTED" appear on the
screen and MD output signal
when movement is detected.
Returns to the level which was
set by the manufacturer for
shipment.
(except for communication and
Day & Night)
Saves all settings, then exits.
Focus is controlled
automatically
Focus is controlled manually
Focus is automatically adjusted
just once, after zoom position
is changed.
Digital zoom limit selectable
(x2 ~ x10).
Zoom magnification set at power
on (x1 ~ x10)
Zoom magnification display off
Zoom magnification display on.
When initialized, zoom position
is disabled.
Execute lens initialization.
Brightness level adjustment.
IRIS is controlled manually.
IRIS is controlled automatically.
Shutter is controlled manually
Automatic gain control off.
Automatic gain control limit set.
Noise reduction level set.
Sense-up limit selectable
(x2 ~ x128)
Using the position preset function,
8 sets of camera shooting
conditions can be stored and
recalled.
AREA(4 Programmable zone)
/ SIZE / TONE adjustable.
IR-Cut Filter is fixed to color
position.
IR-Cut Filter is fixed to B/W
position.
When Input luminance level is
low, IR Cut Filter is switched
to the B/W position for
increasing
infrared sensitivity automatically.
And, it switches back to Color
position when luminance
is quite increased. Auto 1
mode is switched to IR Cut
Filter more quickly than Auto
2.
External Sync(can adjust
desired phase from 0° ~ 359°).
Trigger Signal: Auto Detection.
Refer to communication setup
Refer to communication setup
If the product is to be put out of operation
definitively, take it to a local recycling plant for a
disposal which
is not harmful to the environment.
Comments to this Manuals